<br><font size=2 face="sans-serif">Hello Martin,</font>
<br><font size=2 face="sans-serif">Sten-Åke has generated the tool paths
also for the finishing operation. The tool used, here named T1, is the
same as for Ibusuki (D16 R4 L60). Programmed cutting data is: spindle speed=15000rpm
and feed=3183mm/min. We have made the hole 5mm deeper than the finished
model's bottom surface in order to create enough space for suggested probing
locations.</font>
<br>
<br><font size=2 face="sans-serif">Regards,</font>
<br><font size=2 face="sans-serif">Bengt<br>
<br>
</font><font size=1 face="Verdana"><br>
Bengt Olsson<br>
Sandvik Tooling Sverige AB, TTLP<br>
Office Phone: +46 26-266691<br>
<br>
</font><font size=2 face="sans-serif"><br>
</font><font size=1 color=#808080 face="Verdana">This e-mail is confidential
and it is intended only for the addressees. Any review, dissemination,
distribution, or copying of this message by persons or entities other than
the intended recipient is prohibited. If you have received this e-mail
in error, kindly notify us immediately by telephone or e-mail and delete
the message from your system. The sender does not accept liability for
any errors or omissions in the contents of this message which may arise
as a result of the e-mail transmission.<br>
</font>
<br>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td width=40% bgcolor=white>
<br>
<br>
<br>
<br><font size=1 face="sans-serif"><b>Martin Hardwick <hardwick@steptools.com></b></font>
<br><font size=1 face="sans-serif">2007-09-26 20:45</font>
<td width=59%>
<table width=100%>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">To</font></div>
<td><font size=1 face="sans-serif">bengt.olsson@sandvik.com</font>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">cc</font></div>
<td>
<tr valign=top>
<td>
<div align=right><font size=1 face="sans-serif">Subject</font></div>
<td><font size=1 face="sans-serif">Re: Tool path generation</font></table>
<br>
<table>
<tr valign=top>
<td>
<td></table>
<br></table>
<br>
<br>
<br><font size=3>Hi Bengt,</font>
<br>
<br><font size=3>I have started to assemble the data.</font>
<br>
<br><font size=3>You are using a different origin and orientation for the
part to that used by Airbus. </font>
<br>
<br><font size=3>Can you describe the transformation used to move the geometry
to the new location so that I can do the same in the STEP-NC Explorer.</font>
<br>
<br><font size=3>I need to know any rotations and the XYZ shift.</font>
<br>
<br><font size=3>Martin</font>
<br>
<br><font size=3>At 03:38 AM 9/24/2007, you wrote:</font>
<br>
<br><font size=2>Hi Martin,</font><font size=3> </font>
<br>
<br><font size=2>I have discussed the hole issue with Sten-Åke, and we
suggest that the finishing operation should create a hole 5mm deeper than
the depth of the part model. This means that we would cut 5mm into the
excess stock at the bottom and leave enough clearance for the suggested
probing activity.</font><font size=3> </font>
<br>
<br><font size=2>The roughing paths for the combination of 44 and 20mm
tools are already done. They are the ones you already have:</font><font size=3>
</font>
<br><font size=2> -roughing tool1 (named T10): "UG_Cam_Moriseiki_NH8000.cls"
(44mm diameter tool)</font><font size=3> </font>
<br><font size=2> -roughing tool2 (named T11): "UG_Cam_Moriseiki_NH8000_2.cls"
(20mm diameter tool)</font>
<br>
<br><font size=2>For finishing, one "cls" file for a 16mm tool
will be developed during the week.</font><font size=3> </font>
<br>
<br><font size=2>Are these "cls" files enough for you -or do
you need the "prt" file as well?</font><font size=3> </font>
<br>
<br><font size=2>Regards,</font><font size=3> </font>
<br><font size=2>Bengt</font>
<br>
<br>
<br><font size=1 face="Verdana">Bengt Olsson</font>
<br><font size=1 face="Verdana">Sandvik Tooling Sverige AB, TTLP</font>
<br><font size=1 face="Verdana">Office Phone: +46 26-266691</font>
<br>
<br>